Boiler Repair & Installation in Aurora, CO
No heat, a cold zone, or a boiler short-cycling into winter. We diagnose the actual fault before we quote, then hand you a flat-rate number in writing. No money down.
Call (720) 880-8064 | Request a Free Quote
Boiler repair and installation across Aurora and Arapahoe County
Deft Plumbing repairs, services, and installs residential gas boilers across Aurora, CO, and no-heat calls get same-day diagnosis. Whether the boiler won't fire or one floor stays cold, we find the actual fault first, a stuck circulator, a waterlogged expansion tank, or a dead ignition board, then hand you a flat-rate quote in writing before we touch a part. Licensed, bonded, and insured in Colorado, no money down. No heat right now? Call (720) 880-8064.
This is the boiler-focused companion to our full-service Aurora plumbing page, narrowed down to hydronic heat. Aurora runs real gas-heat housing stock: the older blocks in Original Aurora, Hampden Heights, and Havana Gardens were built when hot-water baseboard was standard, and a lot of those boilers are on their second or third decade. If you want the wider picture of our metro-wide boiler repair and installation service and how the diagnose-first, flat-rate process works, that page covers the method. This one is about getting your Aurora boiler diagnosed and back on line.
Common boiler repair & installation issues we fix in Aurora
No heat, boiler not firing at all
The most common winter call. Before we roll a truck we'll have you check three safe things: the thermostat and its batteries, the boiler's red service switch and breaker, and the pressure gauge (a cold system should read around 12 to 15 psi). If none of that brings the heat back, the fault is inside the system: ignition, gas valve, low water, or a locked-out high limit. That's a same-day call for us. Don't keep resetting a boiler that locks out over and over.
One zone or floor stays cold while the rest heats
The boiler fires but a whole zone won't warm up. On the older multi-zone baseboard systems common through Hampden Heights and Havana Gardens, this is almost always a stuck circulator pump, a failed zone valve, or air locked in that loop. It is rarely the boiler itself. We isolate the dead zone, test the circulator and valve, and bleed the loop rather than condemning the whole unit.
Boiler short-cycles or bangs on the first cold snap
A system that ran fine in October loads up in the first sustained sub-20 degree stretch and the weak part drops. Short-cycling (firing on and off every couple of minutes) wastes gas and hammers the ignition and pump. Usually a waterlogged expansion tank, a bad aquastat, or an oversized boiler. We find which before quoting.
Pressure gauge reads near zero or the relief valve is dripping
A cold system that has fallen to near zero psi has lost water and will lock out. A relief valve that weeps is either doing its job against high pressure or failing on its own. Both point to the expansion tank, the fill valve, or the relief valve, and all three are diagnosable parts, not a reason to replace the boiler. On Aurora's closed-loop municipal supply, a code-required expansion tank is what keeps that pressure stable.
Scaled heat exchanger on Aurora's hard water
Aurora Water and the surrounding supply run roughly 12 to 17 grains per gallon, into the hard range. That calcium fouls the fill water and any indirect hot-water tank tied to the boiler, and it crusts a heat exchanger from the inside so the unit works through an insulating layer. We look at the water the boiler is fed, not just the burner, and flag scaling before it kills the exchanger.
Rich burn or a boiler set to sea-level spec
Aurora sits around 5,400 feet. A gas boiler set up to a national-average spec burns rich at this altitude, wastes fuel, sooties the heat exchanger, and pushes carbon monoxide higher than it should. We confirm the altitude orifice and derated BTU input are correct for your elevation, not just that the unit lights.
What to expect, start to finish
1. Phone triage
Call (720) 880-8064 and tell us what's happening: no heat, a cold zone, banging, a dripping relief valve. We walk you through the three safe checks (thermostat, service switch, pressure gauge) and can often narrow the fault before we arrive.
2. On-site diagnosis, not a guess
We test the actual system: circulator, expansion tank, zone valves, ignition control, system pressure, and combustion. On an Aurora boiler we also check that the altitude derate and orifice are right for the roughly 5,400-foot elevation. We find the real fault before we price anything.
3. Flat-rate written quote, both options where it matters
You get a written flat-rate number before we touch a part. If a targeted repair will hold, that's the quote. If the unit is at the end of its life, we quote repair and replacement side by side so you decide with real numbers. No money down.
4. Repair on the spot when we can
We carry common boiler parts on the truck: circulators, zone valves, thermocouples, and ignition components. Most single-fault repairs finish the same visit, which matters when the house is cold and it's January in Aurora.
5. Permit and inspection on installs and gas work
A boiler installation or replacement, and any new gas supply run, requires an Arapahoe County permit and a pressure test on the gas piping. We pull the permit, run the pressure test, and coordinate the county inspection ourselves, all included in the flat-rate. The inspection schedule is the county's, so we don't promise same-day on permit-required work.
6. Test, walkthrough, and written warranty
We confirm every zone heats, the system holds pressure, combustion is clean, the code-required expansion tank is doing its job, and the altitude setup is correct. We show you the service switch and the pressure gauge so you know what a healthy reading looks like, and you leave with a written warranty.
Why Boiler Work in Aurora Is Its Own Job
Most boiler pages online could be about any town. This one can't, because Aurora stacks specific conditions against a hydronic system, and after working boilers across Arapahoe County we treat each one as part of the diagnosis, not an afterthought.
First, the water. Aurora's supply runs roughly 12 to 17 grains per gallon, well into the hard range, and the Quincy and Smoky Hill pressure zones on the south and east sides push sediment and mineral load through the system in a way that fouls fill water and any indirect hot-water tank tied to the boiler. That hardness scales the inside of a hydronic loop the same way it scales a water heater, and on a boiler it crusts the heat exchanger so the unit fights through an insulating layer. When we service an Aurora boiler we look at the water it's being fed, not just the burner.
Older baseboard housing stock
Second, the housing stock. Original Aurora, Hampden Heights, and Havana Gardens carry a large share of homes built when hot-water baseboard heat was standard, and plenty of those boilers are 15 to 25 years old on multi-zone loops. Age alone is not a verdict, a well-maintained boiler runs 15 to 20 years, but an aging multi-zone baseboard system is exactly where circulators and zone valves give out on the first hard cold snap. We test those parts before we ever talk about the boiler itself.
Altitude and closed-loop code
Third, elevation and pressure. Aurora sits around 5,400 feet, past the derate threshold, so we verify the altitude orifice and derated BTU input on every boiler we touch, because a rich-burning unit wastes gas and raises carbon monoxide. Aurora's municipal supply is a closed-loop system, which means a thermal expansion tank is code-required to absorb the pressure swing as the water heats. A waterlogged or missing expansion tank is one of the most common faults we find behind a weeping relief valve and a locked-out boiler. We check the gas supply can carry the boiler's full BTU draw before we ever fire a new install, and any new gas run gets handled through sizing the gas line for a new boiler and pressure-tested to code first. Call (720) 880-8064 and we'll walk through your system.
Deft Plumbing vs typical Aurora plumber
| What you get | Deft | Typical |
|---|---|---|
| Diagnosis before quote | We test circulator, expansion tank, zone valves, and ignition first | Replacement quoted on a cold-zone symptom |
| Altitude setup | Orifice and BTU input verified for Aurora's ~5,400 ft elevation | Left at sea-level spec, runs rich |
| Expansion tank | Closed-loop thermal expansion tank checked and sized to code | Ignored until the relief valve starts weeping |
| Quote method | Written flat-rate, signed before work starts | Hourly + parts, total unknown until invoice |
| Permit + gas pressure test | We pull the Arapahoe County permit and pressure-test any new gas run | Left to the homeowner, or skipped |
What Aurora homeowners say
"No heat on a Sunday in January. They walked me through the thermostat and pressure gauge on the phone, came out same day, and it was a stuck circulator, not the whole boiler like another company had told me. Quote matched the invoice."
Verified Google review, Aurora, CO
"Diagnosed a waterlogged expansion tank instead of pushing a replacement on our 13-year-old boiler. Honest from the first call and no money down. The house has held heat through two cold snaps since."
Verified Google review, Aurora metro
Aurora boiler repair & installation questions
My boiler isn't firing and I have no heat in Aurora. What should I do first?
Start with three safe checks before you call anyone. Confirm the thermostat is set to heat and swap its batteries. Find the boiler's service switch, usually a red switch that looks like a light switch on or near the unit, and check it and the breaker. Then read the pressure gauge: a cold system should sit around 12 to 15 psi, and a reading near zero means the system lost water and locked out. If none of that restores heat, the fault is inside the system (ignition, gas valve, low water, or a stuck circulator) and it needs a tech. Don't keep resetting a boiler that locks out repeatedly. We run emergency boiler repair with parts on the truck. Call (720) 880-8064.
Do you do emergency boiler repair in Aurora?
Yes. No heat in a Colorado winter is a same-day call, and Aurora's older gas-heat homes in Original Aurora, Hampden Heights, and Havana Gardens are exactly where a circulator or zone valve tends to give out on the first hard freeze. We carry common boiler parts on the truck (circulators, zone valves, thermocouples, ignition components) so most single-fault repairs finish the same visit. You still get a flat-rate number in writing before the work starts. Call (720) 880-8064 and we'll triage it over the phone first.
Should I repair or replace my boiler in Aurora?
It depends on age and the specific fault. Under about 12 years old with a single failed component (circulator, zone valve, expansion tank, ignition board), repair almost always wins because those are parts, not the boiler. Replacement starts to make sense when the heat exchanger is leaking or scaled through, the unit is 15-plus years old with a major part failed, or a repair would cost 40 percent or more of a new boiler. On Aurora's 12 to 17 grain hard water we pay extra attention to the heat exchanger, since scale is what most often pushes an aging unit into the replace column. We hand you repair and replace numbers side by side and let you choose. We don't push replacement, but we won't hide it when it's the cheaper path over the next few years.
How much does a boiler service cost at Denver altitude?
We don't publish a single number, because a boiler service in Aurora is priced to what the diagnosis actually finds, and altitude is part of that diagnosis. At roughly 5,400 feet a boiler has to be derated, so a proper service includes verifying the altitude orifice and BTU input, checking combustion, testing the circulator and expansion tank, and confirming system pressure, not just lighting the burner. What we promise is a written flat-rate number before we touch a part, no money down, and no change without your written approval. That way the altitude and combustion checks are built into the price you sign, not billed as surprise hourly time.
Does a boiler install need a permit in Aurora / Arapahoe County?
Yes. A boiler installation or replacement in Aurora requires a permit through Arapahoe County, and any new gas supply run also requires a pressure test the inspector verifies. We pull the permit, run the pressure test on the gas piping, and coordinate the county inspection ourselves as part of the flat-rate quote. The permit fee is passed through at the county's fixed rate and we don't mark it up. Because the inspection schedule belongs to the county, we don't promise same-day completion on permit-required boiler work, but we handle every step of getting it permitted and signed off.
Combi boiler or system boiler for an Aurora home?
It comes down to your hot-water demand and your gas supply. A combi boiler makes heat and domestic hot water on demand from one unit with no storage tank, which suits smaller Aurora homes with lower simultaneous hot-water use. The tradeoff is that heavy simultaneous draws (two showers plus a dishwasher) can outrun a single combi, and at Aurora's roughly 5,400-foot elevation the derated BTU output eats into the margin a combi needs to serve heat and hot water at once. A system boiler with a separate storage tank handles higher simultaneous demand and often fits the older multi-zone baseboard homes better. We calculate your actual demand and confirm the gas supply can carry the load before recommending either, the same way we won't put a tankless water heater on a gas line that can't feed it.
Why does my boiler need altitude adjustment in Aurora?
Aurora sits around 5,400 feet, and gas burns differently at elevation than at sea level. Manufacturers require BTU input to be derated as elevation climbs, and a boiler left at a national-average spec runs rich here: it wastes fuel, sooties the heat exchanger, and pushes carbon monoxide higher than it should. When we service or install a boiler in Aurora, we confirm the altitude orifice and input rating are correct for your elevation, not just that the unit fires. It's a safety and efficiency check most homeowners never know to ask about. It's also worth a look before the season turns, which is why we point homeowners to get your boiler ready before the first hard freeze.